
A concrete floor needs resurfacing rather than coating when the damage goes deeper than the surface layer — generally when spalling exceeds about 6mm in depth, when cracks are actively moving, or when more than roughly a quarter of the slab area has failed. A coating bonds to whatever is underneath it. If that material is crumbling, the coating fails with it, usually within a year or two.
The distinction matters because resurfacing costs more upfront and coating over a bad slab costs more eventually. Knowing which one your floor needs is the difference between a floor that lasts fifteen years and one that delaminates before the warranty expires.
What Each Process Actually Does
Coating applies a thin resinous layer — typically 0.5mm to 3mm — bonded to the existing slab. The concrete underneath provides all the structural strength. The coating provides chemical resistance, wear resistance, and appearance. Coating assumes the slab beneath is sound.
Resurfacing applies a new cementitious or resinous layer thick enough to replace the failed surface, commonly 6mm to 25mm or more. It rebuilds the wearing surface rather than covering it, which means it can correct depth, profile, and slope problems that a coating cannot touch.
Put simply: a coating protects a good floor. Resurfacing rebuilds a bad one.
Signs Your Floor Needs Resurfacing
Spalling deeper than the coating thickness
If chunks have broken away leaving depressions deeper than a few millimetres, a coating will follow the contour of the damage rather than hide it. You get a floor that is sealed but still visibly broken, and the thin film over the depression wears through first.
Widespread scaling
Toronto’s 40 to 65 annual freeze-thaw cycles produce surface scaling on slabs that were never adequately sealed. Where scaling covers a large proportion of the floor, the entire top layer has lost integrity. Grinding removes some of it, but if sound concrete is only reached at significant depth, resurfacing is the more sensible path.
Active or moving cracks
A dormant crack can be routed, filled, and coated over. A crack that is still moving — because of settlement, thermal cycling, or structural load — will telegraph through any coating applied over it. Moving cracks need the cause addressed first, then a system with enough flexibility or thickness to accommodate residual movement.
Slope and drainage problems
If water pools on your floor, a coating will not fix it. Coatings follow the existing profile. Correcting fall toward a drain requires building up material, which is resurfacing by definition.
Severe surface contamination
Oil, grease, and chemicals that have soaked deep into a slab prevent adhesion. In older Toronto industrial buildings this is common. Where contamination cannot be removed by grinding, removing and rebuilding the surface is often the only reliable answer.
Signs Coating Is the Right Choice
Coating is appropriate when the slab is structurally sound and the issues are cosmetic or protective rather than dimensional:
- Surface is level with no significant depressions
- Cracks are hairline, dormant, and repairable
- Dusting or minor wear without deep deterioration
- Moisture vapour emission readings are within the system’s tolerance, or can be managed with a mitigation primer
- You need chemical resistance, easier cleaning, safety markings, or a specific appearance
A sound slab in a Toronto warehouse or commercial space is usually a strong candidate for commercial and industrial epoxy and polyurethane flooring in Toronto.
The Third Option: Polishing
Where the slab is sound and reasonably flat, polishing is worth considering alongside coating. Rather than adding material, polishing mechanically refines and densifies the concrete itself. There is no film to delaminate, which removes an entire category of failure.
Polishing requires a slab in decent condition — it exposes what is there rather than covering it, so surface defects and patches become part of the finish. For suitable floors, commercial concrete polishing in Toronto delivers durability without a coating’s vulnerability.
How the Assessment Works
A proper evaluation of a Toronto concrete floor covers:
- Depth of deterioration — how far down does the damage go, and where is sound concrete found
- Bond testing — pull-off tests confirm whether the surface can hold a coating
- Moisture vapour emission rate — measured before any system is specified
- Crack behaviour — dormant or active, and what is driving movement
- Flatness and fall — whether the existing profile serves the space
- Contamination — how deep, and whether it can be removed
These findings determine the answer. Anyone quoting a floor without them is estimating, not assessing.
The Cost Logic
Resurfacing costs more than coating on day one. It is still frequently the cheaper decision.
A coating applied over a deteriorating slab does not merely wear out. It fails — delaminating in sheets, taking the compromised concrete with it. The remediation then involves removing both the failed coating and the damaged substrate before you begin again. You pay for the coating twice and the preparation twice.
Where the substrate needs rebuilding, concrete floor surface preparation in Toronto is the foundation the entire system depends on.
Getting a Straight Answer
For industrial and distribution facilities specifically, our warehouse concrete restoration in Toronto covers joint repair, crack routing, and resurfacing of worn slabs.
Armour Guard has assessed and restored concrete floors across Toronto for more than 30 years, in buildings ranging from warehouses to healthcare facilities. We will tell you when a coating is sufficient and when it would be money wasted.
Contact our Toronto flooring team for an on-site assessment of what your slab actually needs.